Accessories For CMM

During measurement, and particularly when scanning, contaminants such as remnants of coolant, dust, oil and oxides build-up on the stylus of your CMM.

These tiny particles of debris must be removed if good metrology is to be maintained. Manual cleaning is time consuming, often requiring re-calibration of the probe angles before use.

MORE…

CMM Enclosures

Basic Enclosure*

  • Self supporting
  • 50mm aluminium frame
  • Locking door
  • Sizes
    • 1.8 x 1.3 x 3.0
    • 2.2 x 2.0 x 3.1
    • 2.5 x 2.0 x 3.1
    • 3.0 x 2.0 x 3.1

Standard Enclosure*

  • Positive air pressure
  • Air filtration
  • Ceiling with interior light
  • Power sockets
  • Sliding window
  • Sizes
    • 1.8 x 1.3 x 3.0
    • 2.2 x 2.0 x 3.1
    • 2.5 x 2.0 x 3.1
    • 3.0 x 2.0 x 3.1

Environmental Enclosure*

  • Air conditioning
  • Room temperature 20¬įC +/-1.5¬įC
  • Outside temperature 15¬įC to 35¬įC
  • Insulated walls and ceiling
  • Sizes
    • 1.8 x 1.3 x 3.0
    • 2.2 x 2.0 x 3.1
    • 2.5 x 2.0 x 3.1
    • 3.0 x 2.0 x 3.1

*: For Altera Series < 10.8

Rotary Tables

For increased flexibility, productivity and efficiency of CMM inspection.

Typical applications that benefit from an additional rotary axis include the measurement of component parts characterised by symmetrical, recurring or internal geometry - including rotating shafts and discs, casings and housings, turbines and compressor parts, and bearing components.

QuadSlimLineTM 

Low profile¬†surface mounted¬†rotary table with integrated air flotation base ‚Äď allows the table to glide effortlessly over the¬†surface when positioning the table on the CMM:

  • Air flotation base
  • Overall height 150mm, 160mm and 200mm
  • Sizes √ė400mm, √ė600mm, √ė800mm,¬†√ė1000mm and √ė1500mm
  • Load capacities up to 7,000kgs
  • Zero backlash drive
  • Threaded hole or T-Slot platen
  • Angular accuracy from 2 arc seconds
  • Angular repeatability from 0.5 arc seconds

Surface mounted rotary table with air base flotation

QuadMaticTM

Ultralow profile, flush mounted rotary table - granite integrated for minimal impact on the CMM measurement volume:

  • Granite intergrated
  • Height above CMM granite table 1mm
  • Sizes √ė400mm, √ė600mm, √ė800mm, √ė1000mm and √ė1500mm
  • Load capacities up to 7,000kgs
  • Zero backlash drive
  • Threaded hole or T-Slot platen
  • Angular accuracy from 2 arc seconds
  • Angular repeatability from 0.5 arc seconds

Flush mounted rotary table

Flexible Fixturing

Enhance the accuracy and throughput of your CMM inspection, with repeatable fixtures which are easy to assemble and adjust and provide a cost effective fixturing solution for repeat inspections.

Fixturing components correctly during inspection is essential for measurement accuracy and reproducibility. LK Metrology fixture kits are designed to support components securely and with minimum force, while providing a clear access path for the probe. A range of clamps, holders and adjustable supports provide great flexibility for fixturing a host of different shape parts and types of material.

M8 thread| 108-Piece Fixture Component Set Advanced set of fixture components with magnetic and pinch clamps in a durable storage case. Each component is labelled to assist with documenting and reassembling frequently used fixture builds.

Handbox Unit

SOLO¬†¬†multi‚Äźfunction¬†handbox¬†for¬†NMC¬†controllers¬† ¬†

The SOLO handbox has been ergonomically designed with time saving features that put the operator in full control. The¬† intuitive keypad provides control over the software,¬† probe and CMM without returning to the PC. For accuracy in¬† manual mode the 3D joystick features touch‚Äźsense technology for smooth motion and precise positioning.

Soft‚Äźtouch buttons offer dual functions and frequently used settings, while LEDs give a visual indication of status and warnings all at your fingertips and in the palm of a hand. Available as standard with new NMC controllers and LK CMMs, or as a retrofit for non LK CMMs with cable lengths ranging from 5 to 25 meters.

Tool Changing Racks

Tool Changing Racks compatible with all Sensors

A wide range of standard and customised changing racks are available through LK Metrology. Revo and PHS tool changin racks are also available. Follows a brief listing of the readily available standard items:

MR5 & MR52

MCR20

SCR200

FCR25

ACR3

Workplates

For integration with large Coordinate Measuring Machines

Standard Cast Iron workplates are available in sizes ranging from 4000X3000mm to 8000X3000mm. Special sizes as well as hole patterns or T-slots are available upon request as well as workplates made of granite or steel.

Automation & Material Handling

LK Metrology can provide a number of solutions for your automation requirements. From fully automated in-line systems to manual pallet loading unloading systems. Please also visit the Automation page in our Solutions section for existing examples or our Process Automation page in our Innovation 4.0 section for further applications and possibilities.

Service Inquiry

    Contact us for more information on our product/service.

    NOTE: By submitting this form, I accept LK's Privacy Policy.